Icemann420
Well-Known Member
Just do your best to keep the water clean and lower those ppm no need for it to be that high it can’t properly use the nutrients with all the bad leaves.
Hello everyone to one amazing community
- Thread starter Mr gar
- Start date
- Thread starter
- #242
Thanks mate appreciate it . Will wait it out like you said .
Have my oxy rezz coming soon with canna nutes . Hope this time I will get it right
- Thread starter
- #243
Last water change I made I set ppm at 700 and after 2 days I added 2 ltrs of water ppm and after another 2 days I added 5 ltrs of water . Ppm drops a little like 200 but after one day it goes up again . pH was stable but now it keeps going down again . And I keep adding pH up to keep it stable as possible
Ganjagrandaddy
Well-Known Member
It does sound like your going to get Hermes if they are flowering on veg light cycle( unless autos ? )
For heat therw are products to help cope with higher temps. I use one called liquid ice but airflow has to be in and out . If in buckets try using frozen bottles to bring res temp down asap. Any damaged leaves need stripping to avoid rot and wasted Energy too i think. There are good products for stress too that may be worth a look. Have used A.n revive and also used superthrive in the past that I feel did help.
For heat therw are products to help cope with higher temps. I use one called liquid ice but airflow has to be in and out . If in buckets try using frozen bottles to bring res temp down asap. Any damaged leaves need stripping to avoid rot and wasted Energy too i think. There are good products for stress too that may be worth a look. Have used A.n revive and also used superthrive in the past that I feel did help.
- Thread starter
- #245
so just got new nutes and a oxy bucket
will out a clone in soon as it is reaady
any advice on the new clone its been in the propagator for a week now and the roots are just popping out
will out a clone in soon as it is reaady
any advice on the new clone its been in the propagator for a week now and the roots are just popping out
- Thread starter
- #246
.
Hello chris hope you are well buddy ....
So I started a clone from a mother I have and it is on the 9 day since transferred it from the propagator . Ppm is at 700 and pH at 5.8 as nutes I am using canna . The bottom leafs are a bit screwed ( turned yellow) but it was normal during the time it was in the propagator and a little burn was because of reflection from the top of the propagator . Yesterday I noticed some small spots on it and was wondering if you can give me some info . I attached some pics for you
Attachments
Ppm is pointless if yer % of recommended nutes is high
How much if Manuf suggested nutes ya using??????????
Tips look like nute burn
How much if Manuf suggested nutes ya using??????????
Tips look like nute burn
- Thread starter
- #248
Ok, so yer at half then
Hmmmmmm
When did tips start showing burnt???
Hmmmmmm
When did tips start showing burnt???
- Thread starter
- #250
well about 3 days ago but the new ones are looking fine i think no ?
i am mostley worries about the small spots on the bottom ones ... worries it has the same fungus as the other one i have witch by the way will be cut down tomorrow as the crystals are 70 percent milky ....
can you seen the small spots ?
What spots
- Thread starter
- #252
Or am I just paranoid
Attachments
That's yer nute issues
I'd back off a bit
Instead of 10ml do like 7, appears a bit hot
I'd back off a bit
Instead of 10ml do like 7, appears a bit hot
- Thread starter
- #254
should i remove some water from the rezz and add add ro instead
next water change is in 5 days
Removing won't solve it
I'd do a rezz change, see how it's effected moving forward
Like I've mentioned, a single DWC is easier to learn than a big rezz system
May try that
I'd do a rezz change, see how it's effected moving forward
Like I've mentioned, a single DWC is easier to learn than a big rezz system
May try that
- Thread starter
- #256
should i have gone with a smaller rezz ...
i am using the oxy bucket
- Thread starter
- #257
Will do sorry I was having some problems with internet .
Will do a water change tody ... Should I raise ppm to 400 with calmag ?
- Thread starter
- #258
Hello mate I am sending a couple of brown spots on 2 of the bottom leafs and some small yellow spots that don't look like nute burn ... I really don't want to go what I went through with the other one with the fungus so please have a look at the attached pictures .... It seems healthy and growing fast but I am concerned . pH is holding stable at 5.8 and ppm at 650 . I am going to buy canna cure just in case too . I tried my best for the pictures but couldn't do better then that . I removed 2 of the last bottom leafs that were being covered by the plant itself this evening . .What do you think please
Attachments
- Thread starter
- #259
Hello mate hope you are doing well !! I have a deal haze witch I took a clone from is now 5 weeks old and almost ready to flower. Today I noticed these small spots on a couple of leafs and wanted you opinion on it if you don’t mind . Ppm is at 700 and ph at 5.9 . No issues on ppm and ph all is falling at normal pace
Attachments
What nutes ya giving her
