Strain(s):
G-13 Haze (10-12+ Week Flowering Time) Cloned by me!
Enclosure:
4 Foot x 4 Foot Gorilla Tent
Lights: Dual MarsII 700 Watt LED's (18-6 Veg / 12/12 Flower)
Controller: C.A.P. XGC-1
Timer: Sentinel Repeating Recycle Timer (5 Seconds ON / 3 minutes OFF)
Intake: 8" Hard Line (Dust Filtered)
Exhaust: 4" Carbon Filter Scrubber / 4" Inline Duct Fan
Air Temperature: Night 68-72 Degrees Fahrenheit / Day 78-84 Degrees Fahrenheit
Root Zone Temperature: 72-76 Degrees Fahrenheit Air Pump Cooled
Reservoir Temperature: 72 Degrees Fahrenheit
CO2: Not yet but soon if all goes well!
System:
DIY 80-100 PSI High Pressure Aeroponic 6-Plant System (6 Inch PVC)
Pots: 3" Net Pot lined with Clay Stone
Mister Heads: 8 - 0.025 Inch Orifice 80-100 PSI Mister Heads
Solenoids: 8 - 110V Brass Instant Open / Always Off Solenoids
Pump: Shurflo Commercial Grade Diaphragm Pump with 2-Gallon Pressurized Accumulator Tank
Filters: Whole House Sediment Filter, 150 Micron Inline Filter, 50 Micro Inline Filter
Pressure Release Valve: 150 PSI Hot Water Heater Valve
Reservoir: 27 Gallon Heavy Duty Tote with Air Stone
Nutrients: Cyco Platinum Series Kit
PH: 5.7
PPM:1000-1500 (1000 to start but will need adjustment up/down to system and strain)
Well if anyone has been wondering where I have been here what I have been doing for about two or three month I have been spending quite a few bucks building my this new HPA system. I broke down my tent grow and built this while I was in transition. My other journal got f*cked while I was on vacation to Chicago (plant sitter) and came back to a mess so pitched them in the trash, bought the strains I wanted.(G-13 Have, Royal Purple Kush, Super Critical and White Rhino.) The G-13 Haze is running in this tent setup and the others are going into my perpetual garage grow which, I will be starting the new journal for even though the mother plants I have already started flowering.
I built this from a ton of research and trial and error along the way. It is constructed of 6-Inch PVC pipe and 1/2" PVC for the drain. It is fed with 3/8" high pressure line. I have a filter as my intake, a filter just before the misters, and a filter on my drain back to the reservoir. I built it so that my reservoir is outside the tent to keep the temperature down. I decided to use a solenoid on each mister head so that if one fails I don't lose two misters only one. I also wired them up on a breaker panel with a breaker for each to both shutdown if needed and for protection should it burn out. Each mister head is accessible to service as needed and I put a shutoff on each so I don't have to shut the system down to do so. I just put the clones in from the cloner with pretty good roots but they need nutes now.
Here are some pictures I will have more to come!
Day 1 (woot!)
G-13 Haze (10-12+ Week Flowering Time) Cloned by me!
Enclosure:
4 Foot x 4 Foot Gorilla Tent
Lights: Dual MarsII 700 Watt LED's (18-6 Veg / 12/12 Flower)
Controller: C.A.P. XGC-1
Timer: Sentinel Repeating Recycle Timer (5 Seconds ON / 3 minutes OFF)
Intake: 8" Hard Line (Dust Filtered)
Exhaust: 4" Carbon Filter Scrubber / 4" Inline Duct Fan
Air Temperature: Night 68-72 Degrees Fahrenheit / Day 78-84 Degrees Fahrenheit
Root Zone Temperature: 72-76 Degrees Fahrenheit Air Pump Cooled
Reservoir Temperature: 72 Degrees Fahrenheit
CO2: Not yet but soon if all goes well!
System:
DIY 80-100 PSI High Pressure Aeroponic 6-Plant System (6 Inch PVC)
Pots: 3" Net Pot lined with Clay Stone
Mister Heads: 8 - 0.025 Inch Orifice 80-100 PSI Mister Heads
Solenoids: 8 - 110V Brass Instant Open / Always Off Solenoids
Pump: Shurflo Commercial Grade Diaphragm Pump with 2-Gallon Pressurized Accumulator Tank
Filters: Whole House Sediment Filter, 150 Micron Inline Filter, 50 Micro Inline Filter
Pressure Release Valve: 150 PSI Hot Water Heater Valve
Reservoir: 27 Gallon Heavy Duty Tote with Air Stone
Nutrients: Cyco Platinum Series Kit
PH: 5.7
PPM:1000-1500 (1000 to start but will need adjustment up/down to system and strain)
Well if anyone has been wondering where I have been here what I have been doing for about two or three month I have been spending quite a few bucks building my this new HPA system. I broke down my tent grow and built this while I was in transition. My other journal got f*cked while I was on vacation to Chicago (plant sitter) and came back to a mess so pitched them in the trash, bought the strains I wanted.(G-13 Have, Royal Purple Kush, Super Critical and White Rhino.) The G-13 Haze is running in this tent setup and the others are going into my perpetual garage grow which, I will be starting the new journal for even though the mother plants I have already started flowering.
I built this from a ton of research and trial and error along the way. It is constructed of 6-Inch PVC pipe and 1/2" PVC for the drain. It is fed with 3/8" high pressure line. I have a filter as my intake, a filter just before the misters, and a filter on my drain back to the reservoir. I built it so that my reservoir is outside the tent to keep the temperature down. I decided to use a solenoid on each mister head so that if one fails I don't lose two misters only one. I also wired them up on a breaker panel with a breaker for each to both shutdown if needed and for protection should it burn out. Each mister head is accessible to service as needed and I put a shutoff on each so I don't have to shut the system down to do so. I just put the clones in from the cloner with pretty good roots but they need nutes now.
Here are some pictures I will have more to come!
Day 1 (woot!)
