Recent content by ace705

Thank's again for all your help RooRman,i'm going to mix up some soil with your advice using some promix,perlite,and worm casting's they sell around here in 30lb bag's. Wish me luck.

The silver pearl i have must have more sativa in it because it get's the donkey dick's on it.It came out kinda leafy and fluffy.I have 2600 watt's of HPS over a 4'x8' area so that cant be it.The kush i had in there with it was dense.I thought maybe it reverted back to veg but the kush...

Thank's for all your help Roorman, I have one last question for you,do you have any experience with Silver Pearl?It seem's to be a fussy bitch.

Thank's for chatting with me Roorman, The bale of promix is 3.8 cf and the the bag i think is 2.8 cf. How many quart's are in a cubic foot of soil? Is one 1gl of soil 4qt's? Just trying to figure out how much each 1gl grow bag hold's. Should i still put worm casting's in if i use all...

Do i still start out with the guano recommended in the feeding schedule since the castings and guano are put in the mix? If i use 20% perlite,20% worm castings,and 5% jamacan guano do i just add it to 55% of a bale of promix bx?Just making sure i understand when you mention...

Thank's for your reply RooRman, What amount of amendments do you add per bale of promix?

Hey RooRman what's happening, I was wondering what soil would be good to use with the guano? because i plan on putting clone's straight into flowering. Pro-mix + perlite?

I dont see my last post,i guess it was to long or something so i'm not typimg all that again. Your right,i'm sure there are alot of people using more power than i am. The cost of electricity and gas has doubled here and with the total power i'm using would increase my bill 200 percent...

I might as well confess as to why i only have one side of the subpanel wired but i'm strapped for cash.Some people might not agree with what i'm doing but here it goe's.

The problem right now is i'm stuck with only 2 slot's because i'm not able to hook up the other side of the panel. My goal is to power 4 1000w light's if possible and put everything else on another 20-amp circuit i have in the main panel. Right now on the 2 20amp breaker's i'm powering...

Thank's for your replie's,your probably right about surging when the light's come on and a 12 hour load would heat em up.The subpanel has 4 slot's and i only have 2 filled because the other half of the panel aint even hooked up. Can the 20-amp breaker's be changed to 30's or would it be to...

Hey all, I have a 60-amp subpanel with two 20-amp breaker's in it for now and each breaker supplie's power to it's own 20-amp plug. I have the yellow simpull romex 12-3 with ground as the feed. Both breaker's are sharing the line(120v). Basically i have a 1000-watt light on each...

Thank's for all the replie's. It was working then a couple hour's later it was not. It alway's had a louder hum than my other ballast which is the same brand. My first one went down and i got lucky because the cheap plastic bridge inside melted and i got some ceramic wire connector's and...

Thank's for replying Boss-G,nothing look's burnt inside and i know the capacitor doe's hold a charge.I'm just curious how to safley test everthing.

What's up everybody. I have a 1000w HPS that stopped working,when i went in the room the light was out. I tried another bulb and all i get is a small hum and nothing else. If i unplug and plug it back up i get the usual thump but just a light hum. Anybody know how to test the...