TestNegative
New Member
If you've never used synthetic urine before it may seem or sound like something difficult to pull off.
Questions like: Am I mixing it properly? How do I make sure the temperature is right? Will they know that I am using synthetic urine?
These are questions, that we here at TestNegative get quite often, but let me tell you that passing a test with synthetic pee is it easier than you may think. There are only a few simple steps that you need to do in order to give your toxin free sample, that will pass both the Emit (instant) test and the GC/MS lab test.
We offer 2 very easy to use options; The Sub-Solution and the Incognito Belt.
The Sub-Solution is our dehydrated version. All that needs to be done to prepare this sample is:
1- Mix the powdered urine with water in the provided mixing container. (This can be done up to 8 hours prior to your test and the container is equipped with a temperature strip right on it)
2 - Take the urine container & the small vial of heat activator powder (heating agent) with you in the stall.
3 - Add about 1/3 of the heat activator supplied in the vial (actual amount will depend on water temperatures. 1/3 of the vial is for room temperature water), close the cap, mix gently for 10 seconds.
4 - Check the temperature on the bottle. If your sample is within the acceptable temperature range, green reading on the temperature strip. If not warm enough repeat step 3. Your target temp is 98°F but anything between 90-100 is acceptable.
5 - Pour synthetic urine into the supplied collection cup and that's it!
Our Incognito Belt, which is our superior pre-mixed option is even easier
1 - Place the supplied heating pad between the bladder bag and the elastic belt then put on the belt around your waist with the bladder bag touching your skin. (it may take anywhere from 15 - 60 minutes to heat up to the proper temperature, depending on the outside environment) Once it reaches the required temperature (which is also indicated in green on the temperature strip) it will hold it's temperature for approx. 8 hours.
2 - Once in the stall, open the clips to allow urine to flow out and you're done!
P.s. Remitting your urine sample below 90°F or over 100°F is pretty much the only thing that can get you busted so pay special attention to the temperature of your sample before remitting it.
If you have any other questions, please feel free to contact our knowledgeable customer service staff @ support@TestNegative.com or by phone at 1.866.900.5656
Questions like: Am I mixing it properly? How do I make sure the temperature is right? Will they know that I am using synthetic urine?
These are questions, that we here at TestNegative get quite often, but let me tell you that passing a test with synthetic pee is it easier than you may think. There are only a few simple steps that you need to do in order to give your toxin free sample, that will pass both the Emit (instant) test and the GC/MS lab test.
We offer 2 very easy to use options; The Sub-Solution and the Incognito Belt.
The Sub-Solution is our dehydrated version. All that needs to be done to prepare this sample is:
1- Mix the powdered urine with water in the provided mixing container. (This can be done up to 8 hours prior to your test and the container is equipped with a temperature strip right on it)
2 - Take the urine container & the small vial of heat activator powder (heating agent) with you in the stall.
3 - Add about 1/3 of the heat activator supplied in the vial (actual amount will depend on water temperatures. 1/3 of the vial is for room temperature water), close the cap, mix gently for 10 seconds.
4 - Check the temperature on the bottle. If your sample is within the acceptable temperature range, green reading on the temperature strip. If not warm enough repeat step 3. Your target temp is 98°F but anything between 90-100 is acceptable.
5 - Pour synthetic urine into the supplied collection cup and that's it!
Our Incognito Belt, which is our superior pre-mixed option is even easier
1 - Place the supplied heating pad between the bladder bag and the elastic belt then put on the belt around your waist with the bladder bag touching your skin. (it may take anywhere from 15 - 60 minutes to heat up to the proper temperature, depending on the outside environment) Once it reaches the required temperature (which is also indicated in green on the temperature strip) it will hold it's temperature for approx. 8 hours.
2 - Once in the stall, open the clips to allow urine to flow out and you're done!
P.s. Remitting your urine sample below 90°F or over 100°F is pretty much the only thing that can get you busted so pay special attention to the temperature of your sample before remitting it.
If you have any other questions, please feel free to contact our knowledgeable customer service staff @ support@TestNegative.com or by phone at 1.866.900.5656