Smallzz420
New Member
This is my first time cloning ever. I though i would share it with you all.
I built my ez-cloner for just under 55$(for everthing) I though about getting a real one, but to pay 300 some odd $$$ to get a ez-cloner is a little steep i thought. So i got on to google looking for DIY stuff and found this guy that gose by the name KingRalph on International Cannagrafic that talks about making one of those ez-clones for under 60 bucks
Here is what i made
this is the pvc set up
i cut 18 sites, you could do more, 18 is alot for me
i cut my rings from some neopreme mats i had
here is it running
This is all good but dose it work??? so let us find out
first off i'd like to say that i have no exp cloning, going by that i figer that i would have a higher rate of failer from my lack of exp. I was shooting for 12 clones so i took 17 cuttings (1 site has my power cords come out it)
i took my cuttings at a 45 and placed them right into water after being cut, they where then placed in the cloner
for water i just used tap i didnt bother with the ph it was really high like me, 7.6 or close to that
it was really nice the clones never wilted the whole time they were in the cloner with no dome, no misting, no any thing just two t8 2ft away
they all rooted in 7 day with the pump on 24/7 and water temp around 71. I dont know how hard of a strian danky doodle is to clone, 100% of my clones rooted. I was very imperssed on how well this worked. I ended up with 5 more clones then was needed for this run. 12 were put it to pot with soil, the smallest were thrown out (it's sad i wish i could have planted them out back)
I think I let the roots grow to big before they where transplanted this is the most wilt i had the whole time. from what i've readed you should transplant when there 1/2 to 3/4 of an inch long. if your doing hydro you can let them grow longer.
they all look alot better after a couple days, really starting to stretch, time to move the lights closer.
thanks for reading
and your input
I built my ez-cloner for just under 55$(for everthing) I though about getting a real one, but to pay 300 some odd $$$ to get a ez-cloner is a little steep i thought. So i got on to google looking for DIY stuff and found this guy that gose by the name KingRalph on International Cannagrafic that talks about making one of those ez-clones for under 60 bucks
Here is what i made
this is the pvc set up
i cut 18 sites, you could do more, 18 is alot for me
i cut my rings from some neopreme mats i had
here is it running
This is all good but dose it work??? so let us find out
first off i'd like to say that i have no exp cloning, going by that i figer that i would have a higher rate of failer from my lack of exp. I was shooting for 12 clones so i took 17 cuttings (1 site has my power cords come out it)
i took my cuttings at a 45 and placed them right into water after being cut, they where then placed in the cloner
for water i just used tap i didnt bother with the ph it was really high like me, 7.6 or close to that
it was really nice the clones never wilted the whole time they were in the cloner with no dome, no misting, no any thing just two t8 2ft away
they all rooted in 7 day with the pump on 24/7 and water temp around 71. I dont know how hard of a strian danky doodle is to clone, 100% of my clones rooted. I was very imperssed on how well this worked. I ended up with 5 more clones then was needed for this run. 12 were put it to pot with soil, the smallest were thrown out (it's sad i wish i could have planted them out back)
I think I let the roots grow to big before they where transplanted this is the most wilt i had the whole time. from what i've readed you should transplant when there 1/2 to 3/4 of an inch long. if your doing hydro you can let them grow longer.
they all look alot better after a couple days, really starting to stretch, time to move the lights closer.
thanks for reading
and your input