Dabber's DIY Vape Pens

Just an addendum to the above...

To go from rosin, to winterized oil, you will need to dissolve the rosin in ethanol, and then proceed with the winterization process. The amount of ethanol needed should be less than 20% of that required to do the full extraction.
 
Just an addendum to the above...

To go from rosin, to winterized oil, you will need to dissolve the rosin in ethanol, and then proceed with the winterization process. The amount of ethanol needed should be less than 20% of that required to do the full extraction.

So if I collected rosin, dissolved it in everclear, winterized it, then boiled off the alcohol, I would have a vaporable product for cartridges?
 
Thank you both for the info. I was under the impression (possibly wrong) that vaping and alcohol that didn’t evaporate off was not so good for you.
Ethanol is added to nicotine vape cartridges to give more of a throat hit.

So if I collected rosin, dissolved it in everclear, winterized it, then boiled off the alcohol, I would have a vaporable product for cartridges?
I THINK so. You may need to cut it with some propylene glycol to get to the needed consistency,
 
I know this is old but I’m curious. Is “purging” when you boil off the alcohol? And if so, how do you know when it’s complete?
You apply heat and preferably a vacuum with a vacuum chamber and vacuum pump
 
It's really the only way to get it all the way out without having to subject the oil to crazy temps. And ALWAYS use food grade solvent!!!!
 
Well pumps and Chambers aren't cheap but they last for a long time. Definitely an investment. You'll certainly get higher quality end product using a vac compared to heat. Both visual and flavor.

You can make an acceptable product without them though.
 
Well said turbo. Yeah I've had my same pump and chamber for years. More vacuum allows you to boil the solution at lower temps and helps preserve more flavor color etc.
 
One way to go could be get a dab press and skip the solvents entirely. Parchment paper and mesh bags would be your only continuing investment. If you're saving your money for something, that might be something to look at. There are lots of vapes out there that will take rosin practically straight off the press.

Ask questions here about rosin and vapes, it's where all the best squishers hang out:
 
One way to go could be get a dab press and skip the solvents entirely. Parchment paper and mesh bags would be your only continuing investment. If you're saving your money for something, that might be something to look at. There are lots of vapes out there that will take rosin practically straight off the press.

Ask questions here about rosin and vapes, it's where all the best squishers hang out:

This thought has crossed my mind too, but I thought I had read somewhere that rosin doesn’t work well in vapes. I’ll have to check that thread out
 
Hello friends and 420 family!

I'm back.

Some of you know me most of you may not. Very brief introduction... I am Kyle AKA the mad dabber, dabs ,dabber or even mad dabs. I've been here off an on a while. I found 420 when we moved to Alaska . I was a stay a home dad looking to save money on growing my own weed instead of paying the crazy dispensary prices. With the help of 420 I did just that but decided to follow my ambitions and entered the cannabis industry where I am now a lab technician at on of the states largest manufacturing companies.

My goal today is to give back some good info I have acquired along my journey.

I know since day one people have frequently wondered how to get their hash into a vape pen for vaporization, well I am here with the procedure!!!

The cool part is by making a winterized oil not only can we vape it, but I can be eaten pure (since it is fully decarbed), dissolved in oil for eddibles, dabbed and flat out smoked.

@Grandpa Tokin has a thread I'm sure you are all familiar with and to get a vapable product we really only need continue from a certain point in his thread.

The other option for making oil is to take pre existing shatter, wax, crumble, bubble hash(or essentially most any concentrate that isnt already able to be used in a vape pen) and prepare it for vaping through a process called winterization.

What is winterized oil?

Winterized oil is a cannabis oil that has most of its fats and waxes removed from it.

One would take a product like any raw or crude extract, dissolve it in ethanol, everclear (or less preferred iso) freeze out fats and waxes and then subsequently filter it for a more pure and refined end product.

This is extremely important in making a oil suitable for cartridges because it requires a certain fluidity to properly function.

So we begin at the beginning, the best place to start!

I would suggest using freshly dried and fully dehydrated material for this process, but as you will notice in the tutorial below gramps uses fresh frozen which ultimately should offer a similar end....


Here begins the tutorial for alcohol extraction... my comments and tips will be in GREEN



Hello everyone! Grandpa’s making some killer oils and I want to share the process I go through. The goal with this particular batch is to get the best I can from the material I’m using. I’m in search of trichome heads and as little green (Chlorophyll) as possible.

We want the Everclear to do its job and extract the best of the best. For the first batch, this means no shaking and just swirling the material slightly in the alcohol. This will extract more THC, terps, and goodies the plant has to offer.

I SUGGEST FREEZING YOUR BUD JARS AND ALCOHOL OVERNIGHT. LOWER TEMPS ALLOW YOU TO PULL MORE CANNIBINOIDS AND LESS CHLOROPHYLL WITH A LONGER SOAK TIME

With that in mind, let’s make some shatter*VAPE CARTS*

*Warning! This process is extremely dangerous if you don’t take care. I am doing this in a large shop with 12 foot ceilings. I make sure there is adequate cross ventilation by keeping a window and a door open to the outside, and a small fan blowing to help circulate to the outside. This is key to not blowing your ass up! You must also ensure there are no open flames...PERIOD! Alcohol fumes are extremely volatile. Be careful damn it! I will not be responsible for you blowing your house up.

Here’s a list of the components that will be used with current US dollar prices at Amazon:

1. I use this griddle, but there are other less expensive options, $30.94: Toastmaster TM-201GR Griddle, 10 x 20", Black
51bkmtyzMJL_SL1000_.jpg


2. Pyrex dish, $11.09: Pyrex Basics 3 Quart Glass Oblong Baking Dish, Clear 8.9 Inch X 13.2 Inch - 3 Qt
61C6eOuU69L_SL1500_.jpg


3. Cake pan, I don’t know where I got mine, but this will do, $13.99: Wilton Recipe Right Non-Stick Biscuit and Brownie Pan, 11 in. x 7 in. (2-Pack)
61PRmuS8sfL_SL1000_.jpg


4. Stainless strainer, $8.99: CHICHIC Set of 3 Stainless Steel Kitchen Fine Strainers Tea Fine Y Mesh Strainers Juice Egg Filter 3 Sieve Colander Sets Wire Filter Mesh for Tea Coffee Food Rice Vegetable with Handle
610X0M01CQL_SL1000_.jpg


5. Large mason jars. I use these because they are on-hand, I usually buy these at Walmart, $6.00: 1 Ball 64oz Wide Mouth Half Gallon Mason Jar
71w54RGAaGL_SL1500_.jpg


6. Unbleached cone coffee filters, the #4s fit the wide mouth mason jars well, $3.99: Melitta No. 4 Cone Coffee Filters, Natural Brown, 100 Count
51vcs5PWuzL.jpg


7. Silicon pad, $11.00: Oil Slick Duo Platinum Cured Medical Grade Silicone Pads, Set of 2, 3.25x4.5" Pads
61B0_VwNPPL_SL1200_.jpg


8. Razor blades.

9. Gloves. It’s sticky-icky!

Please shop around. You can probably find everything cheaper!

The first things I do is gather all my materials. I put the cake pan on the griddle, and put hot water in the cake pan. This is the beginning of a diy double boiler. I turn on the griddle to keep the water hot.

After that I gather the weed, alcohol, mason jars, and filters to begin the process. Today I’m using some fresh frozen bud from my last harvest. The strain is called Amherst Sour Diesel and the seed came from Humbolt.

A41D2713-E0BF-450A-99B7-4D75765BD007.jpeg


I then put the material in a mason jar and cover the weed with the Everclear:


SO YOUR JARS WEED AND ETHANOL (EVERCLEAR) ARE FROZEN ITS EASIER TO SIMPLY PLACE THE FROZEN WEED IN A JAR AND FROZEN PRODUCT IN ANOTHER.

BEESURE TO STORE OVERNIGHT TO ENSURE THE COLDEST POSSIBLE TEMPS.


631434E5-7A47-4AD9-9A71-BC660FDC83AA.jpeg


E70FCCBF-D26B-440E-9990-139C1A95F473.jpeg


I put the lid on the mason jar and let the alcohol and weed just sit for about 15-30 seconds. Then, I slowly swirl (not shaking; remember, we are going for the best of the best here) for another 20-30 seconds.

Since were going for carts we want to pull more than less. Also the low temperature will aid in pulling less undesired compounds.

I WOULD DUMP THE FROZEN ALCOHOL/ ETHANOL / EVERCLEAR OVER THE FROZEN BUD ( ALL IN THE FREEZER WHILE DOOR IS OPEN) let it soak for 1 minute (60 seconds). Open door swish container for 10 to 15 seconds. Let it soak another minute then proceed to the next step (preliminary filtration)


The jar then gets dumped into my stainless strainer. I sit the strainer over a plastic Folgers Coffee container to capture the goodness (naturally it’s been cleaned beforehand and there’s no coffee in it). :tokin:

HUGE THANKS TO GRAMPS for letting me rob that section of his tutorial...


At this point grandpa will continue the soak swirl and strain technique portioning off each seperate swirl into different containers.

The first container should have the most pure solution.

And this is where the processes begin to take a different course....

For our use this doesn't matter as much the idea is just to get as much as we can in that vital 2 minutes and 15 seconds keeping everything as cold as possible!


Okay so now we have a solution of everclear saturated with full spectrum cannabis goodness.

Now we WINTERIZE!!!

That means we just take that jar.full of ethanol/ everclear/ alcohol and freeze it for 48 hours.


Find the darkest coldest depths of your freezer. And leave the jar for 2 days...


After 2 days you will notice a precipitates forming and falling out of the solution as such....

20191017_092132.jpg


These jars contain 15 grams of BHO each that was dissolved in 100% ethanol and frozen for a few days.

Now we just simply screw on 2 coffee filters where the lid would go on the Mason jar. Using the ring to secure and thread them in place.

With a glove pour the solution over the coffee filter into a clean pyrex dish for purging.

Once your solution is purged fully and reduced into an oil, it's time to decarb.

Decarbing the oil will prevent it from "sugaring" (the often slow process in which thca Crystal's form within an oil). It also makes our oil ready for eating infusing. Lastly decarbing will prevent any substantial muffing/bubbling from occurring within the cartridge itself.


In the lab at work we do this with a hot plate and stir bar. Since I doubt any of us (myself included) have access to these we will use the pancake griddle.

Simply kick the temps up high. As you may or may not know from this site or else where decarb is a function of time and temperature. High temp less time gives an effective decarb but doesnt preserve many terpenes.

We want a lower temp with a longer time to preserve the most flavor for our concentrate. I would suggest 250° f for 30 minutes to start. Depending on your dish and the the amount of oil it may be far more or less heat. The time should be standard, since the ide is to watch the oil heat up and start to foam up.

Once the foaming stage is complete, and no new bubbles form the decarb is complete.


This isnt the best example cause its hi dress of grand in a beaker on a hotplate, but you can see the "head" forming on the top like a good dark beer. The idea is to add heat until that head dissipates, indicating that the decarb is complete!

And then folks you just use a syringe to wick up you oil and shoot it into a cartridge you have.

It's really that simple.

Extract.
Winterize.
Purge.
Decarb.
Put that shit in a cart.
Enjoy :ganjamon:

Here is what you end up with...

2019-11-02 23.29.18.jpg



Cheers folks look forward to bringing you more helpful info as the mag has always done for me!
So I have some BHO I had made for me today and I would like to put into vape carts. Now my question is what do I gotta do to make this happen?
 
Back
Top Bottom