I have my best chances with Rye Berry grain. I understand that you can grow any kind of spores in them, but I am not positive. Right now, I have over a dozen jars of it so I may not buy any Rye Berry grain until the end of summer.
TR
TR
Becca's B+, Blue Meanie, Purple Mystic From Spore Genetics & Blue Yeti LC Fun Run
- Thread starter
- #122
All the literature that I've read always specified Rye grain as the grain of choice. Now there are vids on youtube of comparative grows where a bunch of different grains were tested with the same strain of mycelium. If I remember correctly, rye and corn won.
I acquired some Blue Yeti spores, so I will be joining you with a Blue Yeti grow.
I just inoculated a couple Rye grain jars with it.
I need to do some research; what's the difference between Rye grain and Rye Berry grain?
Stay safe and grow well my friend,
Tok..
I just inoculated a couple Rye grain jars with it.
I need to do some research; what's the difference between Rye grain and Rye Berry grain?
Stay safe and grow well my friend,
Tok..
- Thread starter
- #124
Cool, @Tokin Roll . I think you'll like them- they look like pudgy little snow men with brown hats. Hella potent too.
Rye & rye berry are same thing, rye berry is the whole grain and is more nutritious. You should get some good, fast growth with it.
BeccaBuds
Rye & rye berry are same thing, rye berry is the whole grain and is more nutritious. You should get some good, fast growth with it.
BeccaBuds
- Thread starter
- #125
Saturday was 15 days since dunking the Blue Yeti brick in water for 24 hours and still nada so I pretty much decided that was it, then yesterday when I went to dispose of the brick I found fluffy white around the bottom and in a few patches above, too. I can't tell if it is shroom mycelium or contam so now I've changed my mind again and am back in "watch & see" mode. More shrooms would be cool! Pics from yesterday:
- Thread starter
- #126
The Blue Yeti AIO today from 3 angles. I think it's done. This puffy white stuff doesn't look rhizomorphic and no pins have formed. 19 days after dunk. 
- Thread starter
- #127
Prepped 8 rice bags by breaking up and squeezing the rice toward the bottom of the bag, forming the rice roughly into a cube shape and applied a dab of silicone caulk to each to act as a self healing injection port. I'll make the filtered air exchange holes in the tops of the bags just prior to inoculation after the silicone has cured thoroughly (tomorrow or Saturday).
Four will get 2.5mL each B+ liquid culture and the other 4 will be inoculated with 2.5mL each of Blue Meanie Cubes, also using liquid culture I prepared earlier.
For now I've left the Blue Yeti AIO to do it's thing until I need the SAB.
Four will get 2.5mL each B+ liquid culture and the other 4 will be inoculated with 2.5mL each of Blue Meanie Cubes, also using liquid culture I prepared earlier.
For now I've left the Blue Yeti AIO to do it's thing until I need the SAB.
I guess I am the slow man on the pole. Everything looks fantastic @BeccaBuds
I am going to take you lead on the UB bags. I have a bunch I need to use before they go bad.
I will also take your recommendation of using 2.5ml instead of the 1ml I was using.
Time to get to work.
Tok..
I am going to take you lead on the UB bags. I have a bunch I need to use before they go bad.
I will also take your recommendation of using 2.5ml instead of the 1ml I was using.
Time to get to work.
Tok..
- Thread starter
- #129
That's the very same reason I need to get these bags going, Tok. The expiration date is May, 2024, so now is the time!
- Thread starter
- #130
The silicone SHIPs have all cured and bags labelled. This evening I prepared the filters for the rice bags. Each 1" square filter is 4 layers of 3M #1390 Micropore tape.
I'm using 4 layers after discovering 1 layer doesn't do much as it's far too porous. My test method was simply holding a length of the tape up to a light and looking at it with a 5X magnifier. It took four layers to get to where I couldn't see light through it, so 4 layers it is! I made 2 extras just in case.
I'm going to use my soldering iron to make the breather holes in the rice bags. Set to 375F it should be just hot enough to melt the plastic without burning it.
Immediately after I'll adhere a filter tape over the hole, spray the tape with 70% Iso, and microwave the bag for 90 seconds. The 70% Iso and steam from heating the bag will fully sterilize the filter, then after repeating 8 more times, it will be time to
I'm going to use my soldering iron to make the breather holes in the rice bags. Set to 375F it should be just hot enough to melt the plastic without burning it.
Immediately after I'll adhere a filter tape over the hole, spray the tape with 70% Iso, and microwave the bag for 90 seconds. The 70% Iso and steam from heating the bag will fully sterilize the filter, then after repeating 8 more times, it will be time to
- Thread starter
- #131
Opps! I screwed up- The Micropore tape is 3M Part #1530, NOT the part number I posted yesterday. Thought I best correct that!
- Thread starter
- #132
Still haven't inoculated but did some more prep. Moved the Blue Yeti brick from the SAB into a germination tray with a humidity dome as I think there's still a chance of another flush. We'll see!
I also wiped down the SAB, sprayed everywhere inside w/ 70% Iso, closed it back up with FAE ports open and left it to air out. Also got out two sterile 10cc syringes and two sterile 16Ga x 1.5" needles to fill with liquid cultures.
Got the liquid culture jars of B+ and Blue Meanie Cubes out of the refrigerator to warm up. I'll give them a spin on the mag stirrer to break up clumps before filling the syringes.
I also wiped down the SAB, sprayed everywhere inside w/ 70% Iso, closed it back up with FAE ports open and left it to air out. Also got out two sterile 10cc syringes and two sterile 16Ga x 1.5" needles to fill with liquid cultures.
Got the liquid culture jars of B+ and Blue Meanie Cubes out of the refrigerator to warm up. I'll give them a spin on the mag stirrer to break up clumps before filling the syringes.
Your LC's look great @BeccaBuds
They should take off quickly for you.
I have a Blue Yeti that is at the shake and break stage, so I am not to far behind you.
Stay safe and grow well my friend,
Tok..
They should take off quickly for you.
I have a Blue Yeti that is at the shake and break stage, so I am not to far behind you.
Stay safe and grow well my friend,
Tok..
Similar threads
