- Thread starter
- #61
Randyhamlyn3
Well-Known Member
Thanks again
What size wire do I have to use with a 30 amp breaker? I thought it was 14/2 but it has to be smaller
How To Use Progressive Web App aka PWA On 420 Magazine Forum
Note: This feature may not be available in some browsers.
Thanks again
So you suggest a 1000watt sf light. And I'll still put the one I have In for the first week or 2 or flowering?30 amp breakers use a minimum of 10g wire. if your run is over 50ft you'll need to go up a gauge to 8.
if you are building a dedicated circuit you shouldn't need to go above 20a.
30a will power welders and air compressors. i've run both 30's and 50's.
if you stick with the 30a, you can do a sub-panel with two 15a at the grow room end for better distribution, and even greater safety. otherwise just run a standard 15 or 20a at the main box. if you keep with the 30a you will have trouble wiring in regular outlets to power stuff.
i do not want to discourage but those lights are junk and will not perform anywhere near what an sf would. they are not a 1000w light at all, that is just a number they pulled from their asses for advertising purposes. with any experience at all the first thing you will toss are those lights.
So how well do u think the plants will do under a 1000 watt sf or do u think I should buy the 2000watt sf30 amp breakers use a minimum of 10g wire. if your run is over 50ft you'll need to go up a gauge to 8.
if you are building a dedicated circuit you shouldn't need to go above 20a.
30a will power welders and air compressors. i've run both 30's and 50's.
if you stick with the 30a, you can do a sub-panel with two 15a at the grow room end for better distribution, and even greater safety. otherwise just run a standard 15 or 20a at the main box. if you keep with the 30a you will have trouble wiring in regular outlets to power stuff.
i do not want to discourage but those lights are junk and will not perform anywhere near what an sf would. they are not a 1000w light at all, that is just a number they pulled from their asses for advertising purposes. with any experience at all the first thing you will toss are those lights.
What about PB 20000 that seems to be the same as the sfSo how well do u think the plants will do under a 1000 watt sf or do u think I should buy the 2000watt sf
So you suggest a 1000watt sf light. And I'll still put the one I have In for the first week or 2 or flowering?
So how well do u think the plants will do under a 1000 watt sf or do u think I should buy the 2000watt sf
If we knew the size of your grow area & how much you can really afford to spend on a light we could point you to a decent light.What about PB 20000 that seems to be the same as the sf
It's a 4+4 tent 5 seeds and I'd like to stay under 400If we knew the size of your grow area & how much you can really afford to spend on a light we could point you to a decent light.
I think I'll just go with the sf 2000 unless u can tell me another brand cheaper but just as goodIf we knew the size of your grow area & how much you can really afford to spend on a light we could point you to a decent light.
I know them as Aquarium Light Builders so they are in the same ballpark & probably made some changes to their lights to adapt to this line of business.two of the new atreum would do it under 300. i'm not familiar with them, there are a couple sponsored grows going on with them right now. they daisy chain and have dimming.
there are a pile of new builders.Kessell Lighting did the same thing.
Well I still have that other 1000watt I know it's not actually 1000 but if I add that in with the sf 2000 at flower I think from what imheari g and reading this should do fine... Do anyone disagree?budget led has a few options.
the SF is a good rig. they have good drivers and chipsets, which is what you look for. they are a bit under powered i think. i usually go a rig size up for flower. i would use use a light rated for 5x5 in a 4x4.
I think you would have to put your extra light either to 1 side or the rear of the tent & that would give you a 3' x 4' coverage area.Well I still have that other 1000watt I know it's not actually 1000 but if I add that in with the sf 2000 at flower I think from what imheari g and reading this should do fine... Do anyone disagree?
I am going to get 2 1000s of another light that has Samsung parts like the sf that will give me the 4+4 flowering coverage and 5+5 flowering coverageI think you would have to put your extra light either to 1 side or the rear of the tent & that would give you a 3' x 4' coverage area.
Expensive lights don't always mean they are the best lights either. I spent $1050 ea. on 2 - P900's. My 3 Mars Hydro TSW 2000's at $260 ea. blew those expensive lights out of the water.in an SF i would be looking at a 4000 minimum. that's still only a 400 watt draw rig, and twice the size of your largest current consideration.
for comparison i run a 12 pot 600w true draw cob rig in a 4x4 and have a 650w nextlight waiting in the wings.
you can't replace light.
if you go with the 2000 definitely run everything. you'll probably get there with everything. i just don't hold much hope for those budget burples.
don't fret too much .. i know folk who've spent thousands and thousands til they got it right. led is super hard to get correct the first time.